Development of high pressure membraneless alkaline electrolyzer

A technology for cyclic generation of hydrogen and oxygen using electrodes made of variable valency material that does not need the use of separating ion-exchange membranes is presented. The technological solution enables to fabricate electrolyzers for uninterrupted producing high-pressure hydrogen with reduced energy intensity of the production. The total work for compressing 1 m³ of hydrogen and 0.5 m³ of oxygen has been estimated. Results of investigation of influence of discrete supply of DC current to the electrolysis cell, in order to improve the processes of gas evolution and to simplify the power systems of the electrolysis plant, have been considered. There is also considered an electrolysis installation equipped with a thermosorption compressor in which LaNi₅ is used as a hydride-forming compound. The comparative characteristics of the developed electrolyzer and the currently used hydrogen generators are given.     

Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Generation,validation and application of dynamic load profiles in flow measurement using cavitating Herschel–Venturi nozzles

Today, utility meters for water are tested for measurement behavior at stable operating conditions at specified flow rates as part of the approval process. The measurement error that occurs during start and stop or when changing between flow rates may not be taken into account. In addition, there are new technologies whose measuring behavior under real-world conditions is only known to a limited extend. To take these facts into account, a new method has been developed and tested to determine the measurement behavior of water meters under dynamic load profiles as they occur in the real application. For this purpose, a test rig for flow rate measurement was extended by a cavitation nozzle apparatus and the generation of dynamic load profiles was validated. For the cavitation nozzles used, possible factors influencing the flow rate, such as temperature and purity of the water as well as the upstream pressure were investigated. Using different types of domestic water meters, the applicability of the dynamic test procedure was demonstrated and the measurement behavior of the meters was characterised.     

Simulations of NBI fast ion loss in the presence of toroidal field ripple on EAST

NBI fast ion losses in the presence of the toroidal field ripple on EAST have been investigated by using the orbit code GYCAVA and the NBI code TGCO. The ripple effect was included in the upgraded version of the GYCAVA code. It is found that loss regions of NBI fast ions are mainly on the low field side near the edge in the presence of ripple. For co-current NBIs, the synergy effect of ripple and Coulomb collision on fast ion losses is dominant, and fast trapped ions located on the low field side are easily lost. The ripple well loss and the ripple stochastic loss of fast ions have been identified from the heat loads of co-current NBI fast ions. The ripple stochastic loss and the collisioninduced loss are much larger than the ripple well loss. Heat loads of lost fast ions are mainly localized on the right side of the radio frequency wave antennas from the inside view toward the first wall. For counter-current NBIs, the first orbit loss due to the magnetic drift is the dominant loss channel. In addition, fast ion loss fraction with ripple and collision for each NBI linearly increases with the effective charge number, which is related to the pitch angle scattering effect.     

改进的CAGAN在虚拟试衣中的应用

针对CAGAN（Conditional Analogy GAN）换衣后效果模糊，在目标衣服与原始衣服长短不一致时效果一般，相对目标衣服保留过少的细节等问题做了相关研究并对CAGAN进行了改进，提出了新的虚拟试衣方式。经过改进的CAGAN生成一个粗糙的结果，由该结果得到目标衣服穿在模特身上改变形状后的mask，接下来利用mask对目标衣服进行变形，综合变形的衣服和第一步的结果便得到最终的试衣图像。实验结果表明，该方法解决了前面存在的问题，而且取得了非常好的效果。     

某会议室夏季工况不同送风方式下的气流组织数值模拟研究

采用数值模拟软件对××大学科技馆某小型会议室进行数值模拟,以实际测量的数据为边界条件,建立合适的数学和物理模型,得到温度场、速度场以及空气品质场等模拟结果,通过对模拟结果的对比分析,得到了最佳的气流组织设计方案,相关结论可以为室内气流组织方案设计与优化提供参考依据。     

改性聚乳酸发泡技术研究进展

综述了近几年国内外改性聚乳酸（PLA）发泡技术的研究进展，针对PLA在发泡方面熔体强度和结晶性能的不足，介绍了通过加入扩链剂、交联剂、成核剂、纤维和其他聚合物等物质来改善PLA发泡性能的方法、效果和机理；最后，对改性聚乳酸发泡技术的未来发展进行了展望。     

基于工程状态标定的诊断载荷试验识别方法及应用

针对在役公路梁式桥梁由于材料性能退化及外部环境等因素共同作用而导致承载力不足、耐久性降低等问题,开展旧桥力学性能的快速诊断试验研究。通过诊断性载荷试验的理论分析和有限元模型标定流程研究,快速、高效地完成在役公路桥梁的承载力性能测量和评估,从而为在役公路桥梁结构的养护管理提供可靠的技术支持。     

高层建筑中上下相邻双层大跨度钢桁架施工技术

介绍了上海前滩10-01地块(办公及住宅)高层建筑上下相邻双层大跨度钢桁架施工技术。结合项目桁架结构特点,分析讨论了双层桁架的支撑措施布设及安装过程中的注意要点,解决了±0m楼板不能满足双层桁架荷载要求的问题,提出了待下层桁架支撑卸载后,利用下层桁架布设上层桁架支撑,完成上层桁架安装的方案。同时通过有限元计算分析,对桁架施工过程进行计算模拟,研究施工过程的结构位形及内力,保证施工质量与安全。     

一种基于GN算法的动态图划分方法

随着图规模的急剧增长，对动态图进行实时处理的需求日益增加。大多现有的算法针对静态图划分是有效的，直接用其处理动态图会带来较大的通信开销。针对该问题，提出一种基于GN算法的动态图划分方法。首先收集一段时间内加入动态图中的顶点；然后，利用GN算法对这些新加入的顶点进行预划分，产生若干个内部联系紧密的社区；最后，将预划分产生的社区结果插入到已经划分好的当前图中。实验从交叉边数和负载均衡度两方面将该方法与传统流式划分方法进行比较，结果表明， 在公开数据集上，该方法的交叉边数降低了13%，负载均衡度减少了42.3%。由此可见，该方法的划分质量明显优于传统的流式划分方法。